Note: Since completion of the house I have also decided to allow guest bloggers to post articles related to remodeling. This continues the education process.
TIMELINE
Architect Selection - December 2002 through January 2003
Getting a Permit - January 2003 through November 2004
Construction - November 2004 through September 2006
Post Construction - October 2006 through ???
Craftsman Curtain Rod Bracket Installation
Sun, Mar 14 2010 03:05 PM
| Curtain rod brackets, Curtain rods, Curtains, ebony, mahogany, Post Construction
| Permalink
As promised, here are some installation pictures of the curtain rods. A previous blog post shows the manufacturing of the curtain rod brackets.
Rich Wright, the contractor of my house, made the curtain rods and brackets out of left over mahogany from the construction. He had to build a jig to hold the base bracket in place and ensure that it was aligned straight.
This picture shows the mounting really well. There are two screws that mount the base piece into the wall. The cover piece has a hole in the center where a 3-inch screw goes through the rod (not shown) and into the back support bracket. That hole is then filled with an ebony plug.

We ran into an issue with how to do a bracket for a corner window where each window had it's own curtain. Here is the solution, a corner bracket that takes each rod in at a 45 degree angle.
Test fitting a curtain rod into the brackets to make sure everything fits.

Now it's time to make the curtain rods. Each mahogany rod was custom cut to the length required for each window and door. I numbered the ends of the rods when finishing so I could remember where they went later. After some light sanding to bevel all edges, I sprayed on 3 coats of Varathane to seal them. This is the same finish I used on the curtain rod brackets.

Meanwhile, this block of ebony was cut into tiny squares to plug the holes in the brackets after installation.

And now for the final product. Well, almost final. I still haven't put in the ebony plugs but you can't really tell in these pictures. The rods extend one inch past each end of the brackets. The curtains have tabs with buttons so the curtain can be removed if needed.
Rich Wright, the contractor of my house, made the curtain rods and brackets out of left over mahogany from the construction. He had to build a jig to hold the base bracket in place and ensure that it was aligned straight.


This picture shows the mounting really well. There are two screws that mount the base piece into the wall. The cover piece has a hole in the center where a 3-inch screw goes through the rod (not shown) and into the back support bracket. That hole is then filled with an ebony plug.

We ran into an issue with how to do a bracket for a corner window where each window had it's own curtain. Here is the solution, a corner bracket that takes each rod in at a 45 degree angle.

Test fitting a curtain rod into the brackets to make sure everything fits.

Now it's time to make the curtain rods. Each mahogany rod was custom cut to the length required for each window and door. I numbered the ends of the rods when finishing so I could remember where they went later. After some light sanding to bevel all edges, I sprayed on 3 coats of Varathane to seal them. This is the same finish I used on the curtain rod brackets.



Meanwhile, this block of ebony was cut into tiny squares to plug the holes in the brackets after installation.

And now for the final product. Well, almost final. I still haven't put in the ebony plugs but you can't really tell in these pictures. The rods extend one inch past each end of the brackets. The curtains have tabs with buttons so the curtain can be removed if needed.


Add/Review Comments (2)
Craftsman Curtain Rod Brackets
Mon, Jan 19 2009 09:16 PM
| Curtain rods, Curtains, ebony, mahogany, Post Construction
| Permalink
It has been awhile since I posted here so let me give you an update on the curtain rod brackets and show you what we did. My contractor wanted a web site and I needed curtain rod brackets so we bartered services. I had leftover wood and it was easy for him to manufacture so we had a win-win situation here.
The brackets are made from my leftover Honduran mahogany. Here are the long awaited pics of the unfinished brackets and the finishing process.
Here you can see a complete bracket and the two halves that make it up.
The brackets are made from my leftover Honduran mahogany. Here are the long awaited pics of the unfinished brackets and the finishing process.
Here you can see a complete bracket and the two halves that make it up.
The brackets are match drilled. We had to number them to keep the sets together.
All of my materials: curtain rod brackets and Varathane clear semi-gloss.
Taking all of the brackets apart in preparation for finishing. Ebony plugs will fill the holes.
The brackets are apart and ready for finishing with Varathane.
Craftsman Curtain Rods and Curtains
Mon, Oct 20 2008 10:58 AM
| Curtain rod brackets, Curtain rods, Curtains, ebony, mahogany, Post Construction
| Permalink
After 2 years of living here, we are getting ready to put up curtains and rods. The problem we have been having to this point is what will look good and compliment all of the wood. Well, we found something we like but the problem is that it costs anywhere from $200-$400 per curtain rod. The rods are made of oak with small ebony inserts as you can see in the picture.
If you remember, I have a lot of mahogany and ebony left over from the job so we will be using that and make it ourselves. On a related note, my contractor Rich Wright asked me if I could create a web site for him in exchange for some work I may need done. What great timing! Rich will be building the curtain rods in exchange for his site.
Next Page
Be sure to browse the 2,000 picture Photo Gallery for more step-by-step construction details.